Tuesday, 30 June 2015

Fault code Xerox DC 240/242/250/252/260/WC 7655/7665/7675/7755/7765/7775


Fault Code:
Description / Notes:

002-770
The Hard Drive (HDD) is over capacity

003-xxx codes
Generally: Communication Errors between boards in the machine

005-xxx codes
Generally: Document Feeder problems

005-121 thru 005-158
Document Jams

005-194 thru 005-199
Document size mismatch problems

005-275/280
Document Feeder communication errors

005-281 thru 005-283
Document Tray lift problems

005-284
Document APS (Automatic Paper Sensors) failure (there are 3 sensors which detect various paper widths on the Document Feeder)

005-285
Document Nudger up failure

005-286
Document feed-out sensor failure

005-303
Document Tray Interlock is open

005-304
Document Platen Interlock opened during a job

005-305
Document Top Cover Interlock opened during a job

005-306
Document Tray Interlock opened during a job

005-308/309
Document Left Cover is open or opened during a job

005-906 thru 005-918
Document is still detected in feeder after power-on or after closing one of the document door interlocks

010-xxx codes
Generally: Fuser faults

010-311
Open Fuser Thermistor was detected (white connector)

010-319 *
Fuser Heat Control problem *NOTE: This code must be cleared from Diagnostic Mode… details below.

010-320 **
Fuser Overheat problem… (can be reported by any of the 3 thermistors in the fuser) ** NOTE: This code must be cleared from Diagnostic Mode… details below.

010-322 thru 010-323
Fuser Thermistor open circuit detected (NCCenter Sensor or Rear Thermistor)

010-324***
Fuser NVM (Memory) failure *** NOTE: This code must be cleared from Diagnostic Mode… details below.

010-326 thru 010-327
Fuser Heat Control problems

010-330
Fuser Motor failure

010-420
Fuser Module nearing end of life... NOTE: Read below for fuser count reset info.

010-421
Fuser Module "End of Life"… NOTE: If the fuser is still good, you can replace the Fuser Reset Fuse (on top of the fuser) and possibly the Fuser Heat Roll to keep it running.

012-xxx codes
Generally: Finisher problems

013-xxx codes
Generally: Finisher / Booklet Maker problems

016-xxx codes
Generally: Options or Software failures

016-311
Scanner not detected

024-340 thru 024-747
ESS (Network Controller) problems

024-910 thru 024-917
Paper size Sensing problems (in one of the paper drawers)

024-919
Face Up Tray interlock open

024-920/922
Face Down Tray 1 full / Face Down Tray 2 full

024-923/924/ 925
Toner Cartridge Empty - Y / M / C

024-927/930
OCT (Offset Catch Tray) full / Stacker Tray full

024-934 thru 024-939
Paper type mismatch errors

024-946/947/ 948/949
Tray not in position (T1/2/3/4)

024-950/951/ 952/953/954/ 955/956
No Paper in tray (T1/2/3/4/5/6/7)

042-313
Rear Fuser Cooling Fan failure

042-320/321/ 322/323
Drum Motor failures - 320=Y, 321=C, 322=M, 323=K (black)

042-324
IBT Belt Drive Motor failure

042-325
Main Motor failure

042-326
IBT Belt Home position not detected in time

042-327
IBT Belt Position failure

042-328
IBT Belt Edge Sensor failure

042-330
Fuser Exhaust Fan failure

042-331
Blower Motor Fan failure

042-600/601/ 602
Belt Edge timing failures

042-603
Suction Filter end of life

045-xxx codes
Printing communication failures

061-320/321
ROS (Laser Unit) polygon motor failures

061-323 thru 061-607
ROS (Laser Unit) problems

062-357
CCD (Scanner) Fan failure

062-360
Exposure Carriage position failure.

062-371
Exposure Lamp not lighting (or very dim)

071-101 thru 071-105
Paper Jams from Tray 1 at takeaway or registration

071-210
Tray 1 Lift failure

072-101 thru 072-105
Paper jams from Tray 2 at takeaway or registration

072-210
Tray 2 Lift failure

073-101 thru 073-105
Paper jam from Tray 3 at takeaway or registration

073-210
Tray 3 Lift failure

074-101 thru 074-105
Paper jam from Tray 4 at takeaway or registration

074-210
Tray 4 Lift failure

075-100 thru 075-135
Paper jam from Tray 5 at takeaway or registration

075-210/211
Tray 5 Lift failure / Lift down failure

077-103 thru 077-118
Fuser Exit Sensor jam or final Exit Sensor jam.

077-120
Post 2nd BTR Roll Sensor jam

077-123 thru 077-130
Inverter jams

077-300
Front Cover interlock open

077-301
Left Door interlock open

077-302
Right Cover interlock open

077-303
Transfer Module 2 interlock open

077-909
Paper detected in paper path at power-on

078-100 thru 078-151
Paper jam from Tray 6 / High Capacity Feeder (HCF) at takeaway or registration

078-250
Tray 6 (HCF) Lift failure

078-300
HCF (Hi Capacity Feeder) Top Cover interlock open

078-301
HCF Docking Interlock open

089-600 thru 089-617
Image Registration Control problems

091-311
BCR and Black Charge Corotron Cleaner control problem

091-312
Black Charge / Preclean HVPS (Hi Volt Power Supply) failure


091-313
Drum Cartridge CRUM (chip) communication failure

091-320
Black Charge Corona Wire is broken

091-400
Waste Toner Bottle replacement needed soon

091-401
Black Drum Cartridge near end of life

091-403
Black Charge Corotron Assembly near end of life

091-404
Black Charge Corotron Assembly has reached end of life

091-411
Yellow Drum Cartridge near end of life

091-421
Magenta Drum Cartridge near end of life

091-431
Cyan Drum Cartridge near end of life

091-910
Waste Toner Bottle not detected

091-911
Waste Toner Bottle full

091-913
Black Drum Cartridge at end of life

091-914 thru 091-916 or 091-921
Black Drum Cartridge CRUM communication problems

091-917/920/924/925/927
Yellow Drum Cartridge CRUM communication problems

091-918/922/ 928
Magenta Drum Cartridge CRUM communication problems

091-919/923/ 926/929
Cyan Drum Cartridge CRUM communication problems

091-932
Yellow Drum Cartridge end of life

091-933
Magenta Drum Cartridge end of life

091-934
Cyan Drum Cartridge end of life

092-649/650
ADC Sensor Shutter failures

092-651/652
IBT Belt ADC Sensor (MOB ADC) failures

092-653 thru 092-660
ATC (from Developer Unit) problems…653/657=yellow, 654/658=magenta, 655/659=cyan, 656/660=black

093-300
Marking Drawer Interlock open

093-313 thru 093-317
Toner Dispense problems… 314=Y, 315=M, 316=C, 317=K (black)

093-320
Developer Motor failure

093-421 thru 093-425
Toner Cartridges low 421/422=K(black), 423=Y, 424=M, 425=C

093-600 thru 093-912
Toner Dispense problems (600=Y, 601=M, 602=C, 603/912=K(Black),

093-918 thru
Toner CRUM failures (918/924 /925/926/936/ 940=K(black),927/933/937 =Y, 928/934/938 = M , 929/935/939=C

093-940

094-320/321
1st BTR (Transfer Roll) retract or contact problems

094-322/323
2nd BTR (Transfer Roll) retract or contact problems

102-xxx codes
Generally: Network Controller (ESS) problems

112-700
Finisher Punch Dust Box full (hole punch bin)

116-xxx codes
Generally: Network Controller (ESS) problems

123-xxx codes
Generally: UI (control panel) faults

124-xxx codes
Generally: Configuration errors (e.g., serial number disagreement between various boards or machine speed errors, etc)

127-xxx codes
Printing failures



12 comments:

  1. 010-326 error occur while printing,please help how to fix this error and why this error occur suddenly

    ReplyDelete
  2. 091-910 error. Waste container is in machine, but not being recognized. Blown fuse maybe?

    ReplyDelete
  3. 015-387 pl give comment on this error code( 2240 machine model)

    ReplyDelete
  4. 077-120 error came in mu machine i.e fuji xerox docucentre-III c5500
    what is the solution of this?

    ReplyDelete
  5. 010-321 error cor
    what is the sollution on this

    ReplyDelete
  6. 010-321 error code in xerox dc 240
    what is the sollution on this?

    ReplyDelete
  7. Xerox Dc 240 error code 091-320 solution

    ReplyDelete
  8. Please help Xerox 252 Error code 024-934 paper type mismatch
    if i send a print from bypass the paper paper goes in and then just slips inside and shows error 024-934 print driver mismatch
    if you any idea please help

    ReplyDelete